ASTM A694 F60 Flanges and Grade F60 Carbon Steel Blind/ Slip On Flange

One Of India’s Largest manufacturer Of EN 1092-1 ASME SA 694 F60 Weld Neck/ RTJ Flange In Mumbai, India

Due to the high strength and pressure bearing capacity, flanges are usually used for transmission service. They are available in various grades however if you are looking out for the best grade then ASTM A694 F60 Flanges is the one you should be looking for. As per SA 694 F60 RTJ Flanges Manufacturer In India, these flanges are extremely strong and offer high tensile strength. They are resistant to heat and corrosion. Furthermore, these ASME SA 694 F60 Weld Neck Flange also provide good formability and weldability. They can perform well under high pressure and high temperature environments due to their duplex nature.

Carbon Steel F60 Flanges do not have a raised face and allow more space for the gasket to be attached. The metallurgic and mechanical properties of forged Carbon Steel F60 Blind Flanges are said to be better when compared to other grades since the forging process results in direction grain flow. Other transformation processes cannot change the structural integrity of these flanges. Carbon Steel F60 Slip On Flanges when forged gets rid of gases, porosity, and internal cavity. This in turn reduces the faults that are unexpected under fatigue, stress, or impact. Gr F60 Threaded Flange has a corresponding loose end that can be inserted inside of the flange.

The main advantage of High Yield Carbon Steel A694 F60 Lap Joint Flanges is that once the pipe has been welded to the insert stub end the flange can rotate which creates an easy alignment of bolt holes. A694 F60 CS Plate Flanges are said to be the leak proof solution for piping systems. They are widely used in power generation, petrochemical, gas processing, offshore oil drilling, and pharmaceutical industries. Moreover, these High Yield F60 Socket Weld Flanges are also used in equipment such as condensers, heat exchangers, chemical equipment, seawater equipment, and pulp and paper industry equipment.

Table Of Content:

ASTM A694 F60 Mechanical Properties
A694 F60 Yield Strength
ASTM A694 F60 Flanges Elongation
A694 F60 Chemical Composition
ASTM A694 F60 Ultimate Tensile Strength
ASTM A694 F60 Temperature Range
ASTM A694 F60 Material Specification
Carbon Steel F60 Flange Bolting Length
SA 694 F60 Pipe Flange Size Length
Packaging Of ANSI/ ASME B16.5 High Yield F60 Flange Wooden Boxes
ASTM A694 F60 Weld Neck Flange Dimensions
Price List Of Carbon Steel F60 Flanges
ASME SA 694 F60 Flange Tolerance Formula
A694 Gr F60 Gasket Material
ASTM A694 Gr F60 Pipe Flanges Measurement

Types Of ASTM A694 F60 Flanges
SA 694 F60 Lap Joint Flanges Schedule Chart
A694 F60 RF Flange Application For Piping
Carbon Steel F60 Blind Flange Dimensions
ASTM A694 F60 Slip On Flanges Dimensions
Grade F60 Flanges Thickness Calculation
Class 150 High Yield Carbon Steel F60 Flange Dimensions
Face Types Of ASTM A694 F60 Forged Flanges
Steel A694 F60 Flange Marking

ASTM A694 F60 Mechanical Properties

ASTM A694 Grade	Yield Strength (minimum)		Tensile Strength (minimum)		Elongation (minimum)
ASTM A694 Grade	MPa	ksi	MPa	ksi	%
F60	415	60	515	75	20

Buy ANSI / ASME B16.5 Class 150 Carbon Steel F60 Flanges In Various Types Like Grade A694 Blind, Slip On & Raised Face

A694 F60 Yield Strength

Yield Strength min.
MPa	415
ksi	60

ASTM A694 F60 Flanges Elongation

Elongation (min)
%	20

A694 F60 Chemical Composition

ASTM A694 F60 Flanges Chemical Composition
Manganese [Mn]	≤1.60
Phosphorus [P]	≤0.025
Silicon [Si]	0.15-0.35
Carbon [C]	≤0.30
Sulfur [S]	≤0.025

ASTM A694 F60 Ultimate Tensile Strength

Tensile Strength min.
MPa	515
ksi	75

ASTM A694 F60 Temperature Range

Temperature In °F	150# According To ASME B16.5	300# According To ASME B16.5	400# According To ASME B16.5	600# According To ASME B16.5	900# According To ASME B16.5	1500# According To ASME B16.5	2500# According To ASME B16.5
-20 to 100	275	720	960	1440	2160	3600	6000
200	230	600	800	1200	1800	3000	5000
300	205	540	720	1080	1620	2700	4500
400	190	495	660	995	1490	2485	4140
500	170	465	620	930	1395	2330	3880
600	140	435	580	875	1310	2185	3640
650	125	430	575	860	1290	2150	3580
700	110	425	565	850	1275	2125	3540
750	95	415	555	830	1245	2075	3460
800	80	405	540	805	1210	2015	3360
850	65	395	530	790	1190	1980	3300
900	50	390	520	780	1165	1945	3240
950	35	380	510	765	1145	1910	3180
1000	20	320	430	640	965	1605	2675
1050	20	310	410	615	925	1545	2570
1100	20	255	345	515	770	1285	2145
1150	20	200	265	400	595	995	1655
1200	20	155	205	310	465	770	1285
1250	20	115	150	225	340	565	945
1300	20	85	115	170	255	430	715
1350	20	60	80	125	185	310	515
1400	20	50	65	95	145	240	400
1450	15	35	45	70	105	170	285
1500	10	25	35	55	80	135	230

Check Material Specification & Temperature Range, Dimensions And Latest Price Of AWWA C207 High Yield F60 Socket Weld Flanges In India

ASTM A694 F60 Material Specification

Specification List	ASTM A694 F60 Flanges
Pressure Range	150LB/ 300LB/ 400LB/ 600LB/ 900LB/ 1500LB To 2500LB.
Standard	API/ EN 1092-2/ DIN 2561/ DIN 2501/ DIN 2527/ EN 1092-1/ P235GH
Thickness	SCH 180, SCH 80, SCH 40, SCH 160, SCH 120, SCH 5S, SCH 10, XXS etc.
Types	Lap Joint/ Threaded/ Socket Weld/ Reducing/ Blind/ Slip On/ Weld Neck
Size	NPS 1⁄₂" To NPS 48” Inch
Face Type	(RF)/ (RTJ)/ (FF)

Carbon Steel F60 Flange Bolting Length

Size in (Inches)	Size in (Millimeter)	Number of Bolts	Bolt (UNC) Size	RF (Raised Face) Stud Length	Stud (ISO) Size	Machine Flange Bolt Length
1/2	15	4	1/2	55	M14	50
3/4	20	4	1/2	65	M14	50
1	25	4	1/2	65	M14	55
1 1/4	32	4	1/2	70	M14	55
1 1/2	40	4	1/2	70	M14	65
2	50	4	5/8	85	M16	70
2 1/2	65	4	5/8	90	M16	75
3	80	4	5/8	90	M16	75
3 1/2	90	8	5/8	90	M16	75
4	100	8	5/8	90	M16	75
5	125	8	3/4	95	M20	85
6	150	8	3/4	100	M20	85
8	200	8	3/4	110	M20	90
10	250	12	7/8	115	M24	100
12	300	12	7/8	120	M24	100
14	350	12	1	135	M27	115
16	400	16	1	135	M27	115
18	450	16	1 1/8	145	M30	125
20	500	20	1 1/8	160	M30	140
24	600	20	1 1/4	170	M33	150

SA 694 F60 Pipe Flange Size Length

(NPS) For Nominal Pipe Size In (inches)	As Per ASME B16.5 Class 150
(NPS) For Nominal Pipe Size In (inches)	Flange Diameter In (inch)	Bolts Number	Bolt Diameter In (inch)	Bolt Holes (B.H.) Diameter In (inch)	Bolt Circle (B.C.) In(inch)
1/4	3-3/8	4	1/2	0.62	2-1/4
1/2	3-1/2	4	1/2	0.62	2-3/8
3/4	3-7/8	4	1/2	0.62	2-3/4
1	4-1/4	4	1/2	0.62	3-1/8
1-1/4	4-5/8	4	1/2	0.62	3-1/2
1-1/2	5	4	1/2	0.62	3-7/8
2	6	4	5/8	0.75	4-3/4
2-1/2	7	4	5/8	0.75	5-1/2
3	7-1/2	4	5/8	0.75	6
3-1/2	8-1/2	8	5/8	0.75	7
4	9	8	5/8	0.75	7-1/2
5	10	8	3/4	0.88	8-1/2
6	11	8	3/4	0.88	9-1/2
8	13-1/2	8	3/4	0.88	11-3/4
10	16	12	7/8	1	14-1/4
12	19	12	7/8	1	17
14	21	12	1	1.12	18-3/4
16	23-1/2	16	1	1.12	21-1/4
18	25	16	1-1/8	1.25	22-3/4
20	27-1/2	20	1-1/8	1.25	25
24	32	20	1-1/4	1.38	29-1/2

Some Of The Major Locations We Have Supplied ASTM A694 F60 Flanges:

Malaysia, United Kingdom -UK, Europe, UAE

ASTM A694 F60 Flanges

Europe, Malaysia, United Kingdom -UK, UAE

ASME SA 694 F60 Weld Neck Flange

Dammam -KSA, Indonesia, Philippines

SA 694 F60 RTJ Flange

Thailand, France, Qatar, Europe

Carbon Steel F60 Flange

Bangladesh, USA, Germany, Finland

South Africa, Brazil, Saudi Arabia (KSA), Kuwait

Carbon Steel F60 Blind Flange

Brazil, Saudi Arabia (KSA), South Africa, Kuwait

Australia, Nigeria, Turkey, UK, Belgium, Egypt

Carbon Steel F60 Slip On Flange

Australia, Egypt, Nigeria, Turkey, UK, Belgium

Hong Kong, Spain, Oman, Mexico, Poland, Japan

A694 F60 CS Plate Flange

Mexico, Spain, Hong Kong, Poland, Oman, Japan

Iran, Italy, Chile, Singapore, Canada, China

Gr F60 Threaded Flange

Iran, Canada, Singapore, Italy, Chile, China

Packaging Of ANSI/ ASME B16.5 High Yield F60 Flange Wooden Boxes

ASTM A694 F60 Weld Neck Flange Dimensions

Size (NPS) in Inches	NPS (Normal Pipe Size) Size in Millimeter	Outer Diameter For (O.D.)	Thickness Of Weld Neck Flange	Hub Outer Diameter	Weld Neck Outer Diameter	Length Of ASME B16.5 Welding Neck	Daimeter Of WN Bore	Diameter Of RF (Raised Face)	Raised Face (RF) Height	PCD	Face Of Weld
		A	B	C	D	E	F	G	H	I	J
1/2	15	90	9.6	30	21.3	46	-	34.9	2	60.3	1.6
3/4	20	100	11.2	38	26.7	51		42.9	2	69.9	1.6
1	25	110	12.7	49	33.4	54		50.8	2	79.4	1.6
1 1/4	32	115	14.3	59	42.2	56		63.5	2	88.9	1.6
1 1/2	40	125	15.9	65	48.3	60		73	2	98.4	1.6
2	50	150	17.5	78	60.3	62		92.1	2	120.7	1.6
2 1/2	65	180	20.7	90	73	68		104.8	2	139.7	1.6
3	80	190	22.3	108	88.9	68		127	2	152.4	1.6
3 1/2	90	215	22.3	122	101.6	70		139.7	2	177.8	1.6
4	100	230	22.3	135	114.3	75		157.2	2	190.5	1.6
5	125	255	22.3	164	141.3	87		185.7	2	215.9	1.6
6	150	280	23.9	192	168.3	87		215.9	2	241.3	1.6
8	200	345	27	246	219.1	100		269.9	2	298.5	1.6
10	250	405	28.6	305	273	100		323.8	2	362	1.6
12	300	485	30.2	365	323.8	113		381	2	431.8	1.6
14	350	535	33.4	400	355.6	125		412.8	2	476.3	1.6
16	400	595	35	457	406.4	125		469.9	2	539.8	1.6
18	450	635	38.1	505	457.2	138		533.4	2	577.9	1.6
20	500	700	41.3	559	508	143		584.2	2	635	1.6
24	600	815	46.1	663	610	151		692.2	2	749.3	1.6

Get BS 4504 A694 F60 CS Plate Flanges, Low Temperature EN 1092-2 PN16 Gr F60 Threaded Flange For Oil And Gas Industry

Price List Of Carbon Steel F60 Flanges

Type Of Flanges	Size	SCH	Class	Material	Price In INR (India) Per Piece
Weld Neck Flange	2"	SCH STD	150	ASTM A694 F60	397.00
Weld Neck Flange	3"	SCH STD	150	-	521.00
Weld Neck Flange	4"	SCH STD	150	-	623.00
Weld Neck Flange	6"	SCH STD	150	-	700.00
Weld Neck Flange	8"	SCH STD	150	-	912.00
Weld Neck Flange	10"	SCH STD	150	-	1026.00
Blind Flange	3/4"	Sch 40	150	-	127.00
Blind Flange	3/4"	Sch 40	150	-	250.00
Blind Flange	1"	Sch 40	150	-	435.00
Blind Flange	1-1/2"	Sch 40	150	-	484.00
Blind Flange	2"	Sch 40	150	-	569.00
Blind Flange	3"	Sch 40	150	-	768.00
Blind Flange	4"	Sch 40	150	-	984.00
Socket Weld Flange	3/4"	SCH XS	300	-	200.00
Socket Weld Flange	1”	SCH XS	300	-	258.00
Socket Weld Flange	1-1/2"	SCH XS	300	-	569.00
Socket Weld Flange	2"	SCH XS	300	-	680.00
Socket Weld Flange	3"	SCH XS	300	-	869.00
Socket Weld Flange	4"	SCH XS	300	ASTM A694 F60	1021.00
Slip On Flange	1 /1/2"	80	150	-	269.00
Slip On Flange	2"	80	150	-	348.00
Slip On Flange	3"	80	150	-	459.00
Slip On Flange	4"	80	150	-	679.00
Slip On Flange	6"	80	150	ASTM A694 F60	789.00

Biggest Manufacturer Of ASTM A694 F60 Flanges In India. For final Carbon Steel F60 Weld Neck Flanges Price List Please Call on +91-9987870874 or drop an Email to info@fastwell.in.

ASME SA 694 F60 Flange Tolerance Formula

ASTM A694 F60 Flanges	Type Of Daimeter	Tolerance List
(A)	(O.D.) For Outside Diameter	When Outside Diameter is 24 Inch or less: ±1/16" (1.6 mm) When Outside Diameter is over 24": ±1/8" (3.2 mm)
(D)	(I.D.) For Inside Diameter	10 Inch and smaller: ±1/32" (0.8 in mm) 12 Inch thru 18": +1/8" (3.2 in mm) 20 Inch and larger: -1/16" (1.6 in mm)
(B)	Contact Face	1/16" (RF): ±1/32" (0.8 mm) 1/4" (RF), Tongue & Groove (male & female): ±1/64" (0.4 mm)
(J)	Hub At Base Daimeter	When hub base is 24 inch or smaller: ±1/16" (1.6 mm) When hub base is over 24": ±1/8" (3.2 mm)
(H)	Diameter of hub at point of welding	5 inch and smaller: +3/32" (2.4 mm), -1/32" (0.8 mm) 6 inch and larger: +5/32" (4.0 mm), -1/32 (0.8 mm)
(P)	Drilling	Bolt circle (BC): ±1/16" (1.6 mill.) Bolt hole (BH) spacing: ±1/32" (0.8 mill.)
	Eccentricity of bolt circle (bc) with respect to facing	2 1/2" and smaller ±1/32" (0.8 mm) maximum 3" and larger ±1/16" (1.6 mm) maximum
(C)	Wall Thickness	18 inch and smaller: ±1/8" (3.2 mill.), -0" 20 inch and larger: ±3/16" (4.8 mill.), -0"
(K)	hub Length	10 Inch and smaller: ±1/16" (1.6 mm) 12 Inch and larger: ±1/8" (3.2 mm)

A694 Gr F60 Gasket Material

NPS For (Normal Pipe Size)	Gasket (I.D.) Inside Daimeter	Gasket (O.D.) Outside Daimeter
NPS For (Normal Pipe Size)	Gasket (I.D.) Inside Daimeter	#150LB	#300LB	#400LB	#600LB	#900LB
1/2"	0.84	1.875	2.125	2.125	2.125	2.50
3/4"	1.06	2.25	2.625	2.625	2.625	2.75
1"	1.31	2.625	2.875	2.875	2.875	3.125
1 1/4"	1.66	3	3.25	3.25	3.25	3.50
1 1/2"	1.91	3.375	3.75	3.75	3.75	3.875
2"	2.38	4.125	4.375	4.375	4.375	5.625
2 1/2"	2.88	4.875	5.125	5.125	5.125	6.50
3"	3.50	5.375	5.875	5.875	5.875	6.625
4"	4.50	6.875	7.125	7.00	7.625	8.125
5"	5.56	7.75	8.50	8.375	9.50	9.75
6"	6.62	8.75	9.875	9.75	10.50	11.375
8"	8.62	11	12.125	12.00	12.625	14.125
10"	10.75	13.375	14.25	14.125	15.75	17.125
12"	12.75	16.125	16.625	16.50	18.00	19.625

ASTM A694 Gr F60 Pipe Flanges Measurement

C For Thickness of flange
Q For (Minimum) diameter of bolt circle
T For (Minimum) thread length
Y For Length through hub
O For Outside Diameter of flange
X For Hub Diameter at base
R For Diameter of raised face

Types Of ASTM A694 F60 Flanges

SA 694 F60 Blind Flanges

Grade F60 RTJ Flanges

Carbon Steel F60 Threaded Flanges

SA 694 F60 Spectacle Blind Flanges

High Yield F60 Weld Neck Flanges

ASTM A694 F60 Slip On Flanges

ASME SA 694 F60 Raised Face Flanges

CS A694 F60 Forged Flanges

SA 694 F60 Lap Joint Flanges Schedule Chart

Nominal Pipe Size For (NPS)	Slip On Flange (SORF)	Threaded Flange (NPT)	Socket Weld Flange (SWRF)	Lap Joint Flange (Loose)	Blind Flange (BLRF)	Weld Neck Flange (WNRF)
½	1	1	2	1	2	2
¾	2	2	2	2	2	2
1	2	2	2	2	2	3
1¼	3	3	3	3	3	3
1½	3	3	3	3	4	4
2	5	5	5	5	5	6
2½	8	8	8	8	7	10
3	9	9	9	9	9	11.5
3½	11	12	11	11	13	12
4	13	13	13	13	17	16.5
5	15	15	15	15	20	21
6	19	19	19	19	27	26
8	30	30	30	30	47	42
10	43	43	43	43	70	54
12	64	64	64	64	123	88
14	90	90	90	105	140	114
16	106	98	98	140	180	140
18	130	130	130	160	220	165
20	165	165	165	195	285	197
22	185	185	185	245	355	225
24	220	220	220	275	430	268

No Need To Pay Extra When You Can Buy DIN 86029 PN10 Class 300 High Yield Carbon Steel A694 F60 Lap Joint Flanges In Exact Sizes & Schedule, Get Free Quote Now!.

A694 F60 RF Flange Application For Piping

SA 694 F60 RTJ Flange For Heat Exchanger
Gr F60 Threaded Flange For Pulp And Paper Industry
Carbon Steel F60 Flanges For Fluid Piping
Carbon Steel F60 Blind Flanges For Dairy And Food Processing
A694 F60 CS Plate Flanges For Oil And Gas Industry
ASTM A694 F60 Flanges For Power Plants
ASME SA 694 F60 Weld Neck Flange For Modern Architecture

Carbon Steel F60 Blind Flange Dimensions

NPS For (Normal Pipe Size)	Outside Daimeter Of (O.D.) (A)	Wall Thickness Of (B)	Daimeter Of Raised Face (C)	(D) (B.C.D.)	# Flanges Bolts Holes	Daimeter Of Bolt Holes	Approx. Weight In KG (Kilogram)
1/2"	3-1/2	7/16	1-3/8	2-3/8	4	5/8	2
3/4"	3-7/8	1/2	1-11/16	2-3/4	4	5/8	2
1"	4-1/4	9/16	2	3-1/8	4	5/8	2
1-1/4"	4-5/8	5/8	2-1/2	3-1/2	4	5/8	3
1-1/2"	5	11/16	2-7/8	3-7/8	4	5/8	3
2"	6	3/4	3-5/8	4-3/4	4	3/4	4
2-1/2"	7	7/8	4-1/8	5-1/2	4	3/4	7
3"	7-1/2	15/16	5	6	4	3/4	9
3-1/2"	8-1/2	15/16	5-1/2	7	8	3/4	13
4"	9	15/16	6-3/16	7-1/2	8	3/4	17
5"	10	15/16	7-5/16	8-1/2	8	7/8	20
6"	11	1	8-1/2	9-1/2	8	7/8	27
8"	13-1/2	1-1/8	10-5/8	11-3/4	8	7/8	47
10"	16	1-3/16	12-3/4	14-1/4	12	1	67
12"	19	1-1/4	15	17	12	1	123
14"	21	1-3/8	16-1/4	18-3/4	12	1-1/8	139
16"	23-1/2	1-7/16	18-1/2	21-1/4	16	1-1/8	187
18"	25	1-9/16	21	22-3/4	16	1-1/4	217
20"	27-1/2	1-11/16	23	25	20	1-1/4	283
24"	32	1-7/8	27-1/4	29-1/2	20	1-3/8	415

ASTM A694 F60 Slip On Flanges Dimensions

Normal Pipe Size For (NPS)	(Inside Diameter) For I.D.	O.D. For (Outside Daimeter)	B.C. For (Circle Bolt)	Raised (R)	RF For (Raised Face)	H For (Hight)	Raised Face Wall Thickness	Thickness1	Flat Face (FF) (Thickness2)	Bolts Holes For (B.C.)	Number Of Bolt Hole (B.H.)
1/2	0.88	3.50	2.38	1.38	.063	1.19	.62	.38	.56	.62	4
3/4	1.09	3.88	2.75	1.69	.063	1.50	.62	.44	.56	.62	4
1	1.36	4.25	3.12	2.00	.063	1.94	.69	.50	.63	.62	4
1-1/4	1.70	4.62	3.50	2.50	.063	2.31	.81	.56	.75	.62	4
1-1/2	1.97	5.00	3.88	2.88	.063	2.56	.88	.62	.82	.62	4
2	2.44	6.00	4.75	3.62	.063	3.06	1.00	.69	.94	.75	4
2-1/2	2.94	7.00	5.50	4.12	.063	3.56	1.12	.82	1.06	.75	4
3	3.57	7.50	6.00	5.00	.063	4.25	1.19	.88	1.13	.75	4
3-1/2	4.07	8.50	7.00	5.50	.063	4.81	1.25	.88	1.19	.75	8
4	4.57	9.00	7.50	6.19	.063	5.31	1.31	.88	1.25	.75	8
5	5.66	10.00	8.50	7.31	.063	6.44	1.44	.88	1.38	.88	8
6	6.72	11.00	9.50	8.50	.063	7.56	1.56	.94	1.50	.88	8
8	8.72	13.50	11.75	10.62	.063	9.69	1.75	1.06	1.69	.88	8
10	10.88	16.00	14.25	12.75	.063	12.00	1.94	1.13	1.88	1.00	12
12	12.88	19.00	17.00	15.00	.063	14.38	2.19	1.19	2.13	1.00	12
14	14.14	21.00	18.75	16.25	.063	15.75	2.25	1.32	2.19	1.12	12
16	16.16	23.50	21.25	18.50	.063	18.00	2.50	1.38	2.44	1.12	16
18	18.18	25.00	22.75	21.00	.063	19.88	2.69	1.50	2.63	1.25	16
20	20.20	27.50	25.00	23.00	.063	22.00	2.88	1.63	2.83	1.25	20
22	22.22	29.50	27.25	25.25	.063	24.25	3.13	1.75	3.07	1.38	20
24	24.25	32.00	29.50	27.25	.063	26.12	3.25	1.82	3.19	1.38	20

Grade F60 Flanges Thickness Calculation

NPS For Normal Pipe Size	O.D. For (Outside Daimeter)	10 SCH	20 SCH	30 SCH	STD Wall	40 SCH	60 SCH	EXT Hvy	80 SCH	100 SCH	120 SCH	140 SCH	160 SCH	XX Hvy
½	0.84	0.083	...	...	0.109	0.109	...	0.147	0.147	...	...	...	0.188	0.294
¾	1.05	0.083	...	...	0.113	0.113	...	0.154	0.154	...	...	...	0.219	0.308
1	1.315	0.109	...	...	0.133	0.133	...	0.179	0.179	...	...	...	0.25	0.358
1 ¼	1.66	0.109	...	...	0.14	0.14	...	0.191	0.191	...	...	...	0.25	0.382
1 ½	1.9	0.109	...	...	0.145	0.145	...	0.2	0.2	...	...	...	0.281	0.4
2	2.375	0.109	...	...	0.154	0.154	...	0.218	0.218	...	...	...	0.344	0.436
2 ½	2.875	0.12	...	...	0.203	0.203	...	0.276	0.276	...	...	...	0.375	0.552
3	3.5	0.12	-	-	0.216	0.216	-	0.3	0.3	-	-	-	0.438	0.6
3 ½	4	0.12	-	-	0.226	0.226	-	0.318	0.318	-	-	-	-	0.636
4	4.5	0.12	-	-	0.237	0.237	-	0.337	0.337	-	0.438	-	0.531	0.674
5	5.563	0.134	-	-	0.258	0.258	-	0.375	0.375	-	0.5	-	0.625	0.75
6	6.625	0.134	-	-	0.28	0.28	-	0.432	0.432	-	0.562	-	0.719	0.864
8	8.625	0.148	0.25	0.277	0.322	0.322	0.406	0.5	0.5	0.594	0.719	0.812	0.906	0.875
10	10.75	0.165	0.25	0.307	0.365	0.365	0.5	0.5	0.594	0.719	0.844	1	1.125	1
12	12.75	0.18	0.25	0.33	0.375	0.406	0.562	0.5	0.688	0.844	1	1.125	1.312	1
14	14	0.25	0.312	0.375	0.375	0.438	0.594	0.5	0.75	0.938	1.094	1.25	1.406	-
16	16	0.25	0.312	0.375	0.375	0.5	0.656	0.5	0.844	1.031	1.219	1.438	1.594	-
18	18	0.25	0.312	0.438	0.375	0.562	0.75	0.5	0.938	1.156	1.375	1.562	1.781	-
20	20	0.25	0.375	0.5	0.375	0.594	0.812	0.5	1.031	1.281	1.5	1.75	1.969	-
22	22	0.25	-	-	0.375	-	-	0.5	-	-	-	-	-	-
24	24	0.25	0.375	0.562	0.375	0.688	0.969	0.5	1.219	1.531	1.812	2.062	2.344	-
26	26	-	-	-	0.375	-	-	0.5	-	-	-	-	-	-
30	30	0.312	0.5	0.625	0.375	-	-	0.5	-	-	-	-	-	-
36	36	0.312	0.5	0.625	0.375	0.75	-	0.5	-	-	-	-	-	-
40	40	-	-	-	0.375	-	-	0.5	-	-	-	-	-	-
42	42	……..	……..	……..	0.375	……..	……..	0.5	……..	……..	……..	……..	……..	……..
48	48	……..	……..	……..	0.375	……..	……..	0.5	……..	……..	……..	……..	……..	……..

Class 150 High Yield Carbon Steel F60 Flange Dimensions

NPS	(O.D.) For Outside Diameter	Minimum (Wall Thickness) (T)	Diameter Of Raised Face (RF) (R)	Number of Bolts Holes	Dia. of Holes	B.C. For (Bolt Circle)	SORF Bore I.D. (SB)	WNRF Bore I.D. (WB)	Diameter Of Hub Base (H.B.)	Diameter of Hub Top (H.T.)	SORF Length (S.L.)	WNRF Length (W.L.)
¹⁄₂	3.50	0.38	1.38	4	0.62	2.38	0.88	0.62	1.19	0.84	0.56	1.81
³⁄₄	3.88	0.44	1.69	4	0.62	2.75	1.09	0.82	1.50	1.05	0.56	2.00
1	4.25	0.50	2.00	4	0.62	3.12	1.36	1.05	1.94	1.32	0.62	2.12
1¹⁄₄	4.62	0.56	2.50	4	0.62	3.50	1.70	1.38	2.31	1.66	0.75	2.19
1¹⁄₂	5.00	0.62	2.88	4	0.62	3.88	1.95	1.61	2.56	1.90	0.81	2.38
2	6.00	0.69	3.62	4	0.75	4.75	2.44	2.07	3.06	2.38	0.94	2.44
2¹⁄₂	7.00	0.81	4.12	4	0.75	5.50	2.94	2.47	3.56	2.88	1.06	2.69
3	7.50	0.88	5.00	4	0.75	6.00	3.57	3.07	4.25	3.50	1.12	2.69
3¹⁄₂	8.50	0.88	5.50	8	0.75	7.00	4.07	3.55	4.81	4.00	1.19	2.75
4	9.00	0.88	6.19	8	0.75	7.50	4.57	4.03	5.31	4.50	1.25	2.94
5	10.00	0.88	7.31	8	0.88	8.50	5.66	5.05	6.44	5.56	1.38	3.44
6	11.00	0.94	8.50	8	0.88	9.50	6.72	6.07	7.56	6.63	1.50	3.44
8	13.50	1.06	10.62	8	0.88	11.75	8.72	7.98	9.69	8.63	1.69	3.94
10	16.00	1.12	12.75	12	1.00	14.25	10.88	10.02	12.00	10.75	1.88	3.94
12	19.00	1.19	15.00	12	1.00	17.00	12.88	12.00	14.38	12.75	2.12	4.44
14	21.00	1.31	16.25	12	1.12	18.75	14.14	13.25	15.75	14.00	2.19	4.94
16	23.50	1.38	18.50	16	1.12	21.25	16.16	15.25	18.00	16.00	2.44	4.94
18	25.00	1.50	21.00	16	1.25	22.75	18.18	17.25	19.88	18.00	2.62	5.44
20	27.50	1.62	23.00	20	1.25	25.00	20.20	19.25	22.00	20.00	2.81	5.62
22	29.50	1.75	25.25	20	1.38	27.25	22.22	21.25	24.25	22.00	3.07	5.82
24	32.00	1.81	27.25	20	1.38	29.50	24.25	23.25	26.12	24.00	3.19	5.94

Face Types Of ASTM A694 F60 Forged Flanges

Types of Flanges Faces	DIN And EN 1092-1
(RF) For Raised Fac	Form B2
DIN2512 Tongue Flanges	Form C
DIN 2513 Female Flanges	Form F
(RF) For Raised Face	Form B1
(RF) For Raised Face	Form B1
Without (RF) Raised Face	Form A
DIN 2512 Groove Flanges	Form D
DIN 2513 Male Flanges	Form E

Steel A694 F60 Flange Marking

ASTM A694 F60 Flanges Marking includes ANSI Or ASME/ ASA Code

Name of Manufacturer = (Fastwell Engineering)
NPS = (18 Inch)
Flanges Type = (Slip On)
Schedule = (SCH 40)
Material Designation = (ASTM A694 F60)
Class = (1500#)
Country Name = (Made In India)