Carbon steel is widely used in manufacturing flanges and fittings that are used in various industries. CS Flange is one such type of flange that offer different strength and toughness during production and use. According to Carbon Steel Flanges Manufacturer In India, these flanges offer good impact strength because of which the function is improved and the ring stiffness offered is 1.3 times that of solid walls. Large Diameter Carbon Steel Flanges have a service life of approximately 50 years under the specified temperature and pressure. Moreover, High Pressure Carbon Steel Forged Flanges do not fade due to the property of being anti UV and anti-radiation.
CS Pipe Flanges can sustain hydrogenating agents as well as chemical media corrosion. These Normalized CS Flanges are also resistant to acids and alkalis as well as they will not rust or corrode. They do not breed bacteria nor do they cause electrochemical erosion. Carbon Steel Mechanical Joint Flanges provide good thermal insulation as the mechanical thermal conductivity is low. Furthermore, these Carbon Steel Slip On Flanges also provides good heat resistance. The softening temperature is said to be 140 degrees C when the working water temperature is70 degrees C.
Carbon Steel Pipe Flanges are difficult to break and are available at a lower cost. They offer structural stability and can support heavy loads depending upon the requirement. Mild Steel Flange has a raised part that can be attached by bolting or welding. These flanges are used in applications that prioritize strength over corrosion resistance. Carbon Steel Blind Flange is available in the size range of ½ inch to 24 inches. They are used in heavy welding applications and to terminate a pipe. Carbon Steel Plate Flanges are used in press machines, push machines, bevelling machines, and sandblasting machines.
Type Of Flanges | Size | SCH | Class | Material | Price In INR (India) Per Piece |
---|---|---|---|---|---|
Weld Neck Flange | 2" | SCH STD | 150 | Carbon Steel | 267.00 |
Weld Neck Flange | 3" | SCH STD | 150 | 346.00 | |
Weld Neck Flange | 4" | SCH STD | 150 | Carbon Steel | 498.00 |
Weld Neck Flange | 6" | SCH STD | 150 | - | 636.00 |
Weld Neck Flange | 8" | SCH STD | 150 | Carbon Steel | 948.00 |
Weld Neck Flange | 10" | SCH STD | 150 | - | 1372.00 |
Weld Neck Flange | 12" | SCH STD | 150 | Carbon Steel | 1675.00 |
Blind Flange | 3/4" | Sch 40 | 150 | Carbon Steel | 95.00 |
Blind Flange | 3/4" | Sch 40 | 150 | - | 146.00 |
Blind Flange | 1" | Sch 40 | 150 | Carbon Steel | 200.00 |
Blind Flange | 1-1/2" | Sch 40 | 150 | - | 250.00 |
Blind Flange | 2" | Sch 40 | 150 | Carbon Steel | 397.00 |
Blind Flanges | 3" | Sch 40 | 150 | - | 468.00 |
Blind Flanges | 4" | Sch 40 | 150 | - | 579.00 |
Blind Flanges | 6" | Sch 40 | 150 | - | 690.00 |
Blind Flanges | 8" | Sch 40 | 150 | Carbon Steel | 829.00 |
Socket Weld Flange | 3/4" | SCH XS | 300 | Carbon Steel | 100.00 |
Socket Weld Flange | 1” | SCH XS | 300 | - | 145.00 |
Socket Weld Flange | 1-1/2" | SCH XS | 300 | Carbon Steel | 208.00 |
Socket Weld Flange | 2" | SCH XS | 300 | - | 343.00 |
Socket Weld Flange | 3" | SCH XS | 300 | Carbon Steel | 486.00 |
Socket Weld Flange | 4" | SCH XS | 300 | - | 589.00 |
Socket Weld Flange | 6" | SCH XS | 300 | Carbon Steel | 785.00 |
Slip On Flange | 1 /1/2" | 80 | 150 | Carbon Steel | 224.00 |
Slip On Flange | 2" | 80 | 150 | - | 334.00 |
Slip On Flange | 3" | 80 | 150 | Carbon Steel | 467.00 |
Slip On Flange | 4" | 80 | 150 | - | 634.00 |
Slip On Flange | 6" | 80 | 150 | - | 846.00 |
Slip On Flange | 8" | 80 | 150 | Carbon Steel | 1027.00 |
We Are One Of The Most Trusted Carbon Steel Flanges manufacturer In India. For final CS Flanges Price List Please Call on +91-9987870874 or drop an Email to info@fastwell.in.
NPS | (O.D.) For Outside Diameter | Minimum (Wall Thickness) (T) | Diameter Of Raised Face (RF) (R) | Number of Bolts Holes | Dia. of Holes | B.C. For (Bolt Circle) | SORF Bore I.D. (SB) | WNRF Bore I.D. (WB) | Diameter Of Hub Base (H.B.) | Diameter of Hub Top (H.T.) | SORF Length (S.L.) | WNRF Length (W.L.) |
---|---|---|---|---|---|---|---|---|---|---|---|---|
1⁄2 | 3.50 | 0.38 | 1.38 | 4 | 0.62 | 2.38 | 0.88 | 0.62 | 1.19 | 0.84 | 0.56 | 1.81 |
3⁄4 | 3.88 | 0.44 | 1.69 | 4 | 0.62 | 2.75 | 1.09 | 0.82 | 1.50 | 1.05 | 0.56 | 2.00 |
1 | 4.25 | 0.50 | 2.00 | 4 | 0.62 | 3.12 | 1.36 | 1.05 | 1.94 | 1.32 | 0.62 | 2.12 |
11⁄4 | 4.62 | 0.56 | 2.50 | 4 | 0.62 | 3.50 | 1.70 | 1.38 | 2.31 | 1.66 | 0.75 | 2.19 |
11⁄2 | 5.00 | 0.62 | 2.88 | 4 | 0.62 | 3.88 | 1.95 | 1.61 | 2.56 | 1.90 | 0.81 | 2.38 |
2 | 6.00 | 0.69 | 3.62 | 4 | 0.75 | 4.75 | 2.44 | 2.07 | 3.06 | 2.38 | 0.94 | 2.44 |
21⁄2 | 7.00 | 0.81 | 4.12 | 4 | 0.75 | 5.50 | 2.94 | 2.47 | 3.56 | 2.88 | 1.06 | 2.69 |
3 | 7.50 | 0.88 | 5.00 | 4 | 0.75 | 6.00 | 3.57 | 3.07 | 4.25 | 3.50 | 1.12 | 2.69 |
31⁄2 | 8.50 | 0.88 | 5.50 | 8 | 0.75 | 7.00 | 4.07 | 3.55 | 4.81 | 4.00 | 1.19 | 2.75 |
4 | 9.00 | 0.88 | 6.19 | 8 | 0.75 | 7.50 | 4.57 | 4.03 | 5.31 | 4.50 | 1.25 | 2.94 |
5 | 10.00 | 0.88 | 7.31 | 8 | 0.88 | 8.50 | 5.66 | 5.05 | 6.44 | 5.56 | 1.38 | 3.44 |
6 | 11.00 | 0.94 | 8.50 | 8 | 0.88 | 9.50 | 6.72 | 6.07 | 7.56 | 6.63 | 1.50 | 3.44 |
8 | 13.50 | 1.06 | 10.62 | 8 | 0.88 | 11.75 | 8.72 | 7.98 | 9.69 | 8.63 | 1.69 | 3.94 |
10 | 16.00 | 1.12 | 12.75 | 12 | 1.00 | 14.25 | 10.88 | 10.02 | 12.00 | 10.75 | 1.88 | 3.94 |
12 | 19.00 | 1.19 | 15.00 | 12 | 1.00 | 17.00 | 12.88 | 12.00 | 14.38 | 12.75 | 2.12 | 4.44 |
14 | 21.00 | 1.31 | 16.25 | 12 | 1.12 | 18.75 | 14.14 | 13.25 | 15.75 | 14.00 | 2.19 | 4.94 |
16 | 23.50 | 1.38 | 18.50 | 16 | 1.12 | 21.25 | 16.16 | 15.25 | 18.00 | 16.00 | 2.44 | 4.94 |
18 | 25.00 | 1.50 | 21.00 | 16 | 1.25 | 22.75 | 18.18 | 17.25 | 19.88 | 18.00 | 2.62 | 5.44 |
20 | 27.50 | 1.62 | 23.00 | 20 | 1.25 | 25.00 | 20.20 | 19.25 | 22.00 | 20.00 | 2.81 | 5.62 |
22 | 29.50 | 1.75 | 25.25 | 20 | 1.38 | 27.25 | 22.22 | 21.25 | 24.25 | 22.00 | 3.07 | 5.82 |
24 | 32.00 | 1.81 | 27.25 | 20 | 1.38 | 29.50 | 24.25 | 23.25 | 26.12 | 24.00 | 3.19 | 5.94 |
Manufacturer Specifications | Carbon Steel Flanges |
---|---|
Maximum And Manimum Pressure | Class 150 To Class 2500. |
Chemical Composition | Carbon [C] (≤0.35), Manganese [Mn] (0.60-1.05), Phosphorus [P] (≤0.35), Sulfur [S] (≤0.40), Silicon [Si] (0.10-0.35) etc. |
Melting Point (Deg F) | 360 |
Density (lb / cu. in.) | 0.284 |
Manufacturer Types Of CS Flanges For Sale | Lap Joint/ Threaded/ Reducing/ Blind/ Slip On/ Weld Neck/ Socket Weld |
Length | NPS 1⁄₂" To NPS 48” |
CS Flange Face Type | Ring Type Joint/ Raised Face/ Flat Face |
Available CS Flange Grade | ASTM A105 & A105N/ ASTM A350 LF2/ ASTM A694 F42/ F52/ F60/ F65/ F70. |
Schedule | SCH 5S, SCH 10, SCH 40, SCH 80, SCH 120, SCH 160, SCH 180 To XXS. |
Dimensions According to ASME B16.5 | P235GH/ API/ EN 1092-2/ DIN 2561/ DIN 2501/ DIN 2527/ EN 1092-1 |
Manufacturing Forging Methods | Rolling And Cutting, Forging & Casting |
Temperature In °F | 150# According To ASME B16.5 | 300# According To ASME B16.5 | 400# According To ASME B16.5 | 600# According To ASME B16.5 | 900# According To ASME B16.5 | 1500# According To ASME B16.5 | 2500# According To ASME B16.5 |
-20 to 100 | 275 | 720 | 960 | 1440 | 2160 | 3600 | 6000 |
200 | 230 | 600 | 800 | 1200 | 1800 | 3000 | 5000 |
300 | 205 | 540 | 720 | 1080 | 1620 | 2700 | 4500 |
400 | 190 | 495 | 660 | 995 | 1490 | 2485 | 4140 |
500 | 170 | 465 | 620 | 930 | 1395 | 2330 | 3880 |
600 | 140 | 435 | 580 | 875 | 1310 | 2185 | 3640 |
650 | 125 | 430 | 575 | 860 | 1290 | 2150 | 3580 |
700 | 110 | 425 | 565 | 850 | 1275 | 2125 | 3540 |
750 | 95 | 415 | 555 | 830 | 1245 | 2075 | 3460 |
800 | 80 | 405 | 540 | 805 | 1210 | 2015 | 3360 |
850 | 65 | 395 | 530 | 790 | 1190 | 1980 | 3300 |
900 | 50 | 390 | 520 | 780 | 1165 | 1945 | 3240 |
950 | 35 | 380 | 510 | 765 | 1145 | 1910 | 3180 |
1000 | 20 | 320 | 430 | 640 | 965 | 1605 | 2675 |
1050 | 20 | 310 | 410 | 615 | 925 | 1545 | 2570 |
1100 | 20 | 255 | 345 | 515 | 770 | 1285 | 2145 |
1150 | 20 | 200 | 265 | 400 | 595 | 995 | 1655 |
1200 | 20 | 155 | 205 | 310 | 465 | 770 | 1285 |
1250 | 20 | 115 | 150 | 225 | 340 | 565 | 945 |
1300 | 20 | 85 | 115 | 170 | 255 | 430 | 715 |
1350 | 20 | 60 | 80 | 125 | 185 | 310 | 515 |
1400 | 20 | 50 | 65 | 95 | 145 | 240 | 400 |
1450 | 15 | 35 | 45 | 70 | 105 | 170 | 285 |
1500 | 10 | 25 | 35 | 55 | 80 | 135 | 230 |
Carbon Steel Pipe Flanges
United Kingdom -UK, Europe, Malaysia, UAE
Mild Steel Flange
Indonesia, Dammam -KSA, Philippines
Carbon Steel Flanged Fittings
France, Qatar, Thailand, Europe
Carbon Steel Blind Flange
USA, Germany, Bangladesh, Finland
Carbon Steel Plate Flanges
South Africa, Saudi Arabia (KSA), Brazil, Kuwait
Carbon Steel Slip On Flanges
Egypt, UK, Turkey, Nigeria, Australia, Belgium
Carbon Steel Weld Neck Flanges
Hong Kong, Spain, Poland, Mexico, Oman, Japan
Carbon Steel Forged Flanges
Italy, Singapore, Iran, Canada, Chile, China
Size in (Inches) | Size in (Millimeter) | Number of Bolts | Bolt (UNC) Size | RF (Raised Face) Stud Length | Stud (ISO) Size | Machine Flange Bolt Length |
---|---|---|---|---|---|---|
1/2 | 15 | 4 | 1/2 | 55 | M14 | 50 |
3/4 | 20 | 4 | 1/2 | 65 | M14 | 50 |
1 | 25 | 4 | 1/2 | 65 | M14 | 55 |
1 1/4 | 32 | 4 | 1/2 | 70 | M14 | 55 |
1 1/2 | 40 | 4 | 1/2 | 70 | M14 | 65 |
2 | 50 | 4 | 5/8 | 85 | M16 | 70 |
2 1/2 | 65 | 4 | 5/8 | 90 | M16 | 75 |
3 | 80 | 4 | 5/8 | 90 | M16 | 75 |
3 1/2 | 90 | 8 | 5/8 | 90 | M16 | 75 |
4 | 100 | 8 | 5/8 | 90 | M16 | 75 |
5 | 125 | 8 | 3/4 | 95 | M20 | 85 |
6 | 150 | 8 | 3/4 | 100 | M20 | 85 |
8 | 200 | 8 | 3/4 | 110 | M20 | 90 |
10 | 250 | 12 | 7/8 | 115 | M24 | 100 |
12 | 300 | 12 | 7/8 | 120 | M24 | 100 |
14 | 350 | 12 | 1 | 135 | M27 | 115 |
16 | 400 | 16 | 1 | 135 | M27 | 115 |
18 | 450 | 16 | 1 1/8 | 145 | M30 | 125 |
20 | 500 | 20 | 1 1/8 | 160 | M30 | 140 |
24 | 600 | 20 | 1 1/4 | 170 | M33 | 150 |
73072100 | Carbon Steel Flanges | 601 |
Nominal Pipe Size For (NPS) | Slip On Flanges (SORF) | Threaded Flanges (NPT) | Socket Weld Flanges (SWRF) | Lap Joint Flanges (Loose) | Blind Flanges (BLRF) | Weld Neck Flanges (WNRF) |
---|---|---|---|---|---|---|
½ | 1 | 1 | 2 | 1 | 2 | 2 |
¾ | 2 | 2 | 2 | 2 | 2 | 2 |
1 | 2 | 2 | 2 | 2 | 2 | 3 |
1¼ | 3 | 3 | 3 | 3 | 3 | 3 |
1½ | 3 | 3 | 3 | 3 | 4 | 4 |
2 | 5 | 5 | 5 | 5 | 5 | 6 |
2½ | 8 | 8 | 8 | 8 | 7 | 10 |
3 | 9 | 9 | 9 | 9 | 9 | 11.5 |
3½ | 11 | 12 | 11 | 11 | 13 | 12 |
4 | 13 | 13 | 13 | 13 | 17 | 16.5 |
5 | 15 | 15 | 15 | 15 | 20 | 21 |
6 | 19 | 19 | 19 | 19 | 27 | 26 |
8 | 30 | 30 | 30 | 30 | 47 | 42 |
10 | 43 | 43 | 43 | 43 | 70 | 54 |
12 | 64 | 64 | 64 | 64 | 123 | 88 |
14 | 90 | 90 | 90 | 105 | 140 | 114 |
16 | 106 | 98 | 98 | 140 | 180 | 140 |
18 | 130 | 130 | 130 | 160 | 220 | 165 |
20 | 165 | 165 | 165 | 195 | 285 | 197 |
22 | 185 | 185 | 185 | 245 | 355 | 225 |
24 | 220 | 220 | 220 | 275 | 430 | 268 |
Tensile Strength minimum | |
---|---|
MPa | 485 |
ksi | 70 |
NPS For (Normal Pipe Size) | Outside Daimeter Of (O.D.) (A) | Wall Thickness Of (B) | Daimeter Of Raised Face (C) | (D) (B.C.D.) | # Flanges Bolts Holes | Daimeter Of Bolt Holes | Approx. Weight In KG (Kilogram) |
---|---|---|---|---|---|---|---|
1/2" | 3-1/2 | 7/16 | 1-3/8 | 2-3/8 | 4 | 5/8 | 2 |
3/4" | 3-7/8 | 1/2 | 1-11/16 | 2-3/4 | 4 | 5/8 | 2 |
1" | 4-1/4 | 9/16 | 2 | 3-1/8 | 4 | 5/8 | 2 |
1-1/4" | 4-5/8 | 5/8 | 2-1/2 | 3-1/2 | 4 | 5/8 | 3 |
1-1/2" | 5 | 11/16 | 2-7/8 | 3-7/8 | 4 | 5/8 | 3 |
2" | 6 | 3/4 | 3-5/8 | 4-3/4 | 4 | 3/4 | 4 |
2-1/2" | 7 | 7/8 | 4-1/8 | 5-1/2 | 4 | 3/4 | 7 |
3" | 7-1/2 | 15/16 | 5 | 6 | 4 | 3/4 | 9 |
3-1/2" | 8-1/2 | 15/16 | 5-1/2 | 7 | 8 | 3/4 | 13 |
4" | 9 | 15/16 | 6-3/16 | 7-1/2 | 8 | 3/4 | 17 |
5" | 10 | 15/16 | 7-5/16 | 8-1/2 | 8 | 7/8 | 20 |
6" | 11 | 1 | 8-1/2 | 9-1/2 | 8 | 7/8 | 27 |
8" | 13-1/2 | 1-1/8 | 10-5/8 | 11-3/4 | 8 | 7/8 | 47 |
10" | 16 | 1-3/16 | 12-3/4 | 14-1/4 | 12 | 1 | 67 |
12" | 19 | 1-1/4 | 15 | 17 | 12 | 1 | 123 |
14" | 21 | 1-3/8 | 16-1/4 | 18-3/4 | 12 | 1-1/8 | 139 |
16" | 23-1/2 | 1-7/16 | 18-1/2 | 21-1/4 | 16 | 1-1/8 | 187 |
18" | 25 | 1-9/16 | 21 | 22-3/4 | 16 | 1-1/4 | 217 |
20" | 27-1/2 | 1-11/16 | 23 | 25 | 20 | 1-1/4 | 283 |
24" | 32 | 1-7/8 | 27-1/4 | 29-1/2 | 20 | 1-3/8 | 415 |
Normal Pipe Size For (NPS) | (Inside Diameter) For I.D. | O.D. For (Outside Daimeter) | B.C. For (Circle Bolt) | Raised (R) | RF For (Raised Face) | H For (Hight) | Raised Face Wall Thickness | Thickness1 | Flat Face (FF) (Thickness2) | Bolts Holes For (B.C.) | Number Of Bolt Hole (B.H.) |
---|---|---|---|---|---|---|---|---|---|---|---|
1/2 | 0.88 | 3.50 | 2.38 | 1.38 | .063 | 1.19 | .62 | .38 | .56 | .62 | 4 |
3/4 | 1.09 | 3.88 | 2.75 | 1.69 | .063 | 1.50 | .62 | .44 | .56 | .62 | 4 |
1 | 1.36 | 4.25 | 3.12 | 2.00 | .063 | 1.94 | .69 | .50 | .63 | .62 | 4 |
1-1/4 | 1.70 | 4.62 | 3.50 | 2.50 | .063 | 2.31 | .81 | .56 | .75 | .62 | 4 |
1-1/2 | 1.97 | 5.00 | 3.88 | 2.88 | .063 | 2.56 | .88 | .62 | .82 | .62 | 4 |
2 | 2.44 | 6.00 | 4.75 | 3.62 | .063 | 3.06 | 1.00 | .69 | .94 | .75 | 4 |
2-1/2 | 2.94 | 7.00 | 5.50 | 4.12 | .063 | 3.56 | 1.12 | .82 | 1.06 | .75 | 4 |
3 | 3.57 | 7.50 | 6.00 | 5.00 | .063 | 4.25 | 1.19 | .88 | 1.13 | .75 | 4 |
3-1/2 | 4.07 | 8.50 | 7.00 | 5.50 | .063 | 4.81 | 1.25 | .88 | 1.19 | .75 | 8 |
4 | 4.57 | 9.00 | 7.50 | 6.19 | .063 | 5.31 | 1.31 | .88 | 1.25 | .75 | 8 |
5 | 5.66 | 10.00 | 8.50 | 7.31 | .063 | 6.44 | 1.44 | .88 | 1.38 | .88 | 8 |
6 | 6.72 | 11.00 | 9.50 | 8.50 | .063 | 7.56 | 1.56 | .94 | 1.50 | .88 | 8 |
8 | 8.72 | 13.50 | 11.75 | 10.62 | .063 | 9.69 | 1.75 | 1.06 | 1.69 | .88 | 8 |
10 | 10.88 | 16.00 | 14.25 | 12.75 | .063 | 12.00 | 1.94 | 1.13 | 1.88 | 1.00 | 12 |
12 | 12.88 | 19.00 | 17.00 | 15.00 | .063 | 14.38 | 2.19 | 1.19 | 2.13 | 1.00 | 12 |
14 | 14.14 | 21.00 | 18.75 | 16.25 | .063 | 15.75 | 2.25 | 1.32 | 2.19 | 1.12 | 12 |
16 | 16.16 | 23.50 | 21.25 | 18.50 | .063 | 18.00 | 2.50 | 1.38 | 2.44 | 1.12 | 16 |
18 | 18.18 | 25.00 | 22.75 | 21.00 | .063 | 19.88 | 2.69 | 1.50 | 2.63 | 1.25 | 16 |
20 | 20.20 | 27.50 | 25.00 | 23.00 | .063 | 22.00 | 2.88 | 1.63 | 2.83 | 1.25 | 20 |
22 | 22.22 | 29.50 | 27.25 | 25.25 | .063 | 24.25 | 3.13 | 1.75 | 3.07 | 1.38 | 20 |
24 | 24.25 | 32.00 | 29.50 | 27.25 | .063 | 26.12 | 3.25 | 1.82 | 3.19 | 1.38 | 20 |
ø | (D) | (B) | (G) | (M) | (J) | (K) | (H) | (L) | Weight In Kilogram (KG) |
1/2" | 88,9 | 11,1 | 34,9 | 30,2 | 22,3 | 60,3 | 4 | 15,9 | 0,400 |
3/4" | 98,4 | 12,7 | 42,9 | 38,1 | 27,7 | 69,8 | 4 | 15,9 | 0,700 |
1" | 107,9 | 14,3 | 50,8 | 49,2 | 34,5 | 79,4 | 4 | 15,9 | 0,800 |
1 1/4" | 117,5 | 15,9 | 63,5 | 58,8 | 43,2 | 88,9 | 4 | 15,9 | 1,100 |
1 1/2" | 127,0 | 17,5 | 73,0 | 65,1 | 49,5 | 98,4 | 4 | 15,9 | 1,400 |
2" | 152,4 | 19,0 | 92,1 | 77,8 | 62,0 | 120,6 | 4 | 19,0 | 2,200 |
2 1/2" | 177,8 | 22,2 | 104,8 | 90,5 | 74,7 | 139,7 | 4 | 19,0 | 3,600 |
3" | 190,5 | 23,8 | 127,0 | 107,9 | 90,7 | 152,4 | 4 | 19,0 | 4,100 |
3 1/2" | 215,9 | 23,8 | 139,7 | 122,2 | 103,4 | 177,8 | 8 | 19,0 | 5,200 |
4" | 228,6 | 23,8 | 157,2 | 134,9 | 116,1 | 190,5 | 8 | 19,0 | 5,600 |
5" | 254,0 | 23,8 | 185,7 | 163,6 | 143,8 | 215,9 | 8 | 22,2 | 6,300 |
6" | 279,4 | 25,4 | 215,9 | 192,1 | 170,7 | 241,3 | 8 | 22,2 | 7,500 |
8" | 342,9 | 28,6 | 269,9 | 246,1 | 221,5 | 298,4 | 8 | 22,2 | 12,600 |
10" | 406,4 | 30,2 | 323,8 | 304,8 | 276,3 | 361,9 | 12 | 25,4 | 18,500 |
12" | 482,6 | 31,7 | 381,0 | 365,1 | 327,1 | 431,8 | 12 | 25,5 | 28,000 |
14" | 533,4 | 34,9 | 412,7 | 400,0 | 359,1 | 476,2 | 12 | 28,6 | 36,000 |
16" | 596,9 | 36,5 | 469,9 | 457,2 | 410,5 | 539,7 | 16 | 28,6 | 46,000 |
18" | 635,0 | 39,7 | 533,4 | 504,8 | 461,8 | 577,8 | 16 | 31,7 | 50,000 |
20" | 698,5 | 42,9 | 584,2 | 558,8 | 513,1 | 635,0 | 20 | 31,7 | 64,000 |
22" | 749,3 | 46,0 | 641,2 | 609,6 | 564,4 | 692,1 | 20 | 34,9 | 72,000 |
24" | 812,8 | 47,6 | 692,1 | 663,6 | 615,9 | 749,3 | 20 | 34,9 | 89,000 |
Size (NPS) in Inches | NPS (Normal Pipe Size) Size in Millimeter | Outer Diameter For (O.D.) | Thickness Of Weld Neck Flange | Hub Outer Diameter | Weld Neck Outer Diameter | Length Of ASME B16.5 Welding Neck | Daimeter Of WN Bore | Diameter Of RF (Raised Face) | Raised Face (RF) Height | PCD | Face Of Weld |
A | B | C | D | E | F | G | H | I | J | ||
1/2 | 15 | 90 | 9.6 | 30 | 21.3 | 46 | - | 34.9 | 2 | 60.3 | 1.6 |
3/4 | 20 | 100 | 11.2 | 38 | 26.7 | 51 | 42.9 | 2 | 69.9 | 1.6 | |
1 | 25 | 110 | 12.7 | 49 | 33.4 | 54 | 50.8 | 2 | 79.4 | 1.6 | |
1 1/4 | 32 | 115 | 14.3 | 59 | 42.2 | 56 | 63.5 | 2 | 88.9 | 1.6 | |
1 1/2 | 40 | 125 | 15.9 | 65 | 48.3 | 60 | 73 | 2 | 98.4 | 1.6 | |
2 | 50 | 150 | 17.5 | 78 | 60.3 | 62 | 92.1 | 2 | 120.7 | 1.6 | |
2 1/2 | 65 | 180 | 20.7 | 90 | 73 | 68 | 104.8 | 2 | 139.7 | 1.6 | |
3 | 80 | 190 | 22.3 | 108 | 88.9 | 68 | 127 | 2 | 152.4 | 1.6 | |
3 1/2 | 90 | 215 | 22.3 | 122 | 101.6 | 70 | 139.7 | 2 | 177.8 | 1.6 | |
4 | 100 | 230 | 22.3 | 135 | 114.3 | 75 | 157.2 | 2 | 190.5 | 1.6 | |
5 | 125 | 255 | 22.3 | 164 | 141.3 | 87 | 185.7 | 2 | 215.9 | 1.6 | |
6 | 150 | 280 | 23.9 | 192 | 168.3 | 87 | 215.9 | 2 | 241.3 | 1.6 | |
8 | 200 | 345 | 27 | 246 | 219.1 | 100 | 269.9 | 2 | 298.5 | 1.6 | |
10 | 250 | 405 | 28.6 | 305 | 273 | 100 | 323.8 | 2 | 362 | 1.6 | |
12 | 300 | 485 | 30.2 | 365 | 323.8 | 113 | 381 | 2 | 431.8 | 1.6 | |
14 | 350 | 535 | 33.4 | 400 | 355.6 | 125 | 412.8 | 2 | 476.3 | 1.6 | |
16 | 400 | 595 | 35 | 457 | 406.4 | 125 | 469.9 | 2 | 539.8 | 1.6 | |
18 | 450 | 635 | 38.1 | 505 | 457.2 | 138 | 533.4 | 2 | 577.9 | 1.6 | |
20 | 500 | 700 | 41.3 | 559 | 508 | 143 | 584.2 | 2 | 635 | 1.6 | |
24 | 600 | 815 | 46.1 | 663 | 610 | 151 | 692.2 | 2 | 749.3 | 1.6 |
Normal Pipe Size For (NPS) in Inches | Normal Pipe Size For (NPS) in Millimeter | Outer Diameter For (O.D.) | Wall Thickness | Lapped Thick. | Lapped (I.D.) For Inside Daimeter | PCD | Thickness Of Lapped | Radius Of Lapped | Bolts No. | Bolts UNC Size | Machine Bolt Length | Length Of Stud (RF) | Size Of Bolts Hole | Size Of ISO Stud | Weight In KG (Kilogram) |
A | B | C | D | E | G | ||||||||||
1/2 | 15 | 90 | 30 | 16 | 22.9 | 60.3 | 11.2 | 3 | 4 | 1/2 | 50 | 55 | 5/8 | M14 | 0.8 |
3/4 | 20 | 100 | 38 | 16 | 28.2 | 69.9 | 12.7 | 3 | 4 | 1/2 | 50 | 65 | 5/8 | M14 | 0.9 |
1 | 25 | 110 | 49 | 17 | 34.9 | 79.4 | 14.3 | 3 | 4 | 1/2 | 55 | 65 | 5/8 | M14 | 0.9 |
1 1/4 | 32 | 115 | 59 | 21 | 43.7 | 88.9 | 15.9 | 5 | 4 | 1/2 | 55 | 70 | 5/8 | M14 | 1.4 |
1 1/2 | 40 | 125 | 65 | 22 | 50 | 98.4 | 17.5 | 6 | 4 | 1/2 | 65 | 70 | 5/8 | M14 | 1.4 |
2 | 50 | 150 | 78 | 25 | 62.5 | 120.7 | 19.1 | 8 | 4 | 5/8 | 70 | 85 | 3/4 | M16 | 2.3 |
2 1/2 | 65 | 180 | 90 | 29 | 75.4 | 139.7 | 22.3 | 8 | 4 | 5/8 | 75 | 90 | 3/4 | M16 | 3.2 |
3 | 80 | 190 | 108 | 30 | 91.4 | 152.4 | 23.9 | 10 | 4 | 5/8 | 75 | 90 | 3/4 | M16 | 3.7 |
3 1/2 | 90 | 215 | 122 | 32 | 104.1 | 177.8 | 23.9 | 11 | 8 | 5/8 | 75 | 90 | 3/4 | M16 | 5 |
4 | 100 | 230 | 135 | 33 | 116.8 | 190.5 | 23.9 | 11 | 8 | 5/8 | 75 | 90 | 3/4 | M16 | 5.9 |
5 | 125 | 255 | 164 | 36 | 144.4 | 215.9 | 23.9 | 11 | 8 | 3/4 | 85 | 95 | 7/8 | M20 | 6.8 |
6 | 150 | 280 | 192 | 40 | 171.4 | 241.3 | 25.4 | 13 | 8 | 3/4 | 85 | 100 | 7/8 | M20 | 8.6 |
8 | 200 | 345 | 246 | 44 | 222.2 | 298.5 | 28.6 | 13 | 8 | 3/4 | 90 | 110 | 7/8 | M20 | 13.7 |
10 | 250 | 405 | 305 | 49 | 277.4 | 362 | 30.2 | 13 | 12 | 7/8 | 100 | 115 | 1 | M24 | 19.5 |
12 | 300 | 485 | 365 | 56 | 328.2 | 431.8 | 31.8 | 13 | 12 | 7/8 | 100 | 120 | 1 | M24 | 29 |
14 | 350 | 535 | 400 | 79 | 360.2 | 476.3 | 35 | 13 | 12 | 1 | 115 | 135 | 1 1/8 | M27 | 41 |
16 | 400 | 595 | 457 | 87 | 411.2 | 539.8 | 36.6 | 13 | 16 | 1 | 115 | 135 | 1 1/8 | M27 | 54 |
18 | 450 | 635 | 505 | 97 | 462.3 | 577.9 | 39.7 | 13 | 16 | 1 1/8 | 125 | 145 | 1 1/4 | M30 | 59 |
20 | 500 | 700 | 559 | 103 | 514.4 | 635 | 42.9 | 13 | 20 | 1 1/8 | 140 | 160 | 1 1/4 | M30 | 75 |
24 | 600 | 815 | 663 | 111 | 616 | 749.3 | 47.9 | 13 | 20 | 1 1/4 | 150 | 170 | 1 3/8 | M33 | 100 |
Density (lb / cu. in.) | 0.284 |
---|
Temperature (in F°) | Class 300 |
< 100 | 740 |
200 | 680 |
300 | 655 |
400 | 635 |
500 | 605 |
600 | 570 |
650 | 550 |
700 | 530 |
750 | 505 |
800 | 410 |
850 | 320 |
900 | 230 |
950 | 135 |
1000 | 85 |
(NPS) For Nominal Pipe Size In (inches) | As Per ASME B16.5 Class 150 | ||||
---|---|---|---|---|---|
Flange Diameter In (inch) | Bolts Number | Bolt Diameter In (inch) | Bolt Holes (B.H.) Diameter In (inch) | Bolt Circle (B.C.) In(inch) | |
1/4 | 3-3/8 | 4 | 1/2 | 0.62 | 2-1/4 |
1/2 | 3-1/2 | 4 | 1/2 | 0.62 | 2-3/8 |
3/4 | 3-7/8 | 4 | 1/2 | 0.62 | 2-3/4 |
1 | 4-1/4 | 4 | 1/2 | 0.62 | 3-1/8 |
1-1/4 | 4-5/8 | 4 | 1/2 | 0.62 | 3-1/2 |
1-1/2 | 5 | 4 | 1/2 | 0.62 | 3-7/8 |
2 | 6 | 4 | 5/8 | 0.75 | 4-3/4 |
2-1/2 | 7 | 4 | 5/8 | 0.75 | 5-1/2 |
3 | 7-1/2 | 4 | 5/8 | 0.75 | 6 |
3-1/2 | 8-1/2 | 8 | 5/8 | 0.75 | 7 |
4 | 9 | 8 | 5/8 | 0.75 | 7-1/2 |
5 | 10 | 8 | 3/4 | 0.88 | 8-1/2 |
6 | 11 | 8 | 3/4 | 0.88 | 9-1/2 |
8 | 13-1/2 | 8 | 3/4 | 0.88 | 11-3/4 |
10 | 16 | 12 | 7/8 | 1 | 14-1/4 |
12 | 19 | 12 | 7/8 | 1 | 17 |
14 | 21 | 12 | 1 | 1.12 | 18-3/4 |
16 | 23-1/2 | 16 | 1 | 1.12 | 21-1/4 |
18 | 25 | 16 | 1-1/8 | 1.25 | 22-3/4 |
20 | 27-1/2 | 20 | 1-1/8 | 1.25 | 25 |
24 | 32 | 20 | 1-1/4 | 1.38 | 29-1/2 |
Specific Heat (Btu/lb/Deg F - [32-212 Deg F]) | 0.107 |
---|
HBW | 137-187 |
---|
Types of Flanges Faces | DIN And EN 1092-1 |
---|---|
Without (RF) Raised Face | Form A |
(RF) For Raised Face | Form B1 |
(RF) For Raised Face | Form B1 |
(RF) For Raised Fac | Form B2 |
DIN2512 Tongue Flanges | Form C |
DIN 2512 Groove Flanges | Form D |
DIN 2513 Male Flanges | Form E |
DIN 2513 Female Flanges | Form F |
Yield Strength min. | |
---|---|
MPa | 250 |
ksi | 36 |
NPS For (Normal Pipe Size) | Gasket (I.D.) Inside Daimeter | Gasket (O.D.) Outside Daimeter | ||||
---|---|---|---|---|---|---|
#150LB | #300LB | #400LB | #600LB | #900LB | ||
1/2" | 0.84 | 1.875 | 2.125 | 2.125 | 2.125 | 2.50 |
3/4" | 1.06 | 2.25 | 2.625 | 2.625 | 2.625 | 2.75 |
1" | 1.31 | 2.625 | 2.875 | 2.875 | 2.875 | 3.125 |
1 1/4" | 1.66 | 3 | 3.25 | 3.25 | 3.25 | 3.50 |
1 1/2" | 1.91 | 3.375 | 3.75 | 3.75 | 3.75 | 3.875 |
2" | 2.38 | 4.125 | 4.375 | 4.375 | 4.375 | 5.625 |
2 1/2" | 2.88 | 4.875 | 5.125 | 5.125 | 5.125 | 6.50 |
3" | 3.50 | 5.375 | 5.875 | 5.875 | 5.875 | 6.625 |
4" | 4.50 | 6.875 | 7.125 | 7.00 | 7.625 | 8.125 |
5" | 5.56 | 7.75 | 8.50 | 8.375 | 9.50 | 9.75 |
6" | 6.62 | 8.75 | 9.875 | 9.75 | 10.50 | 11.375 |
8" | 8.62 | 11 | 12.125 | 12.00 | 12.625 | 14.125 |
10" | 10.75 | 13.375 | 14.25 | 14.125 | 15.75 | 17.125 |
12" | 12.75 | 16.125 | 16.625 | 16.50 | 18.00 | 19.625 |
Thermal Conductivity | 360 |
---|
Carbon Steel Flanges Marking includes ANSI Or ASME/ ASA Code
Flanges Size in (Inches) | Flanges Size in (Millimeter) | Radial Projection (Maximum) | |
---|---|---|---|
No Deeper Than the Bottom In MM | Deeper Than the Bottom In MM | ||
1/2 | 15 | 3.0 | 1.5 |
3/4 | 20 | 3.0 | 1.5 |
1 | 25 | 3.0 | 1.5 |
1 1/4 | 32 | 3.0 | 1.5 |
1 1/2 | 40 | 3.0 | 1.5 |
2 | 50 | 3.0 | 1.5 |
2 1/2 | 65 | 3.0 | 1.5 |
3 | 80 | 4.5 | 1.5 |
3 1/2 | 90 | 6.0 | 3.0 |
4 | 100 | 6.0 | 3.0 |
5 | 125 | 6.0 | 3.0 |
6 | 150 | 6.0 | 3.0 |
8 | 200 | 8.0 | 4.5 |
10 | 250 | 8.0 | 4.5 |
12 | 300 | 8.0 | 4.5 |
14 | 350 | 8.0 | 4.5 |
16 | 400 | 10.0 | 4.5 |
18 | 450 | 12.0 | 6.0 |
20 | 500 | 12.0 | 6.0 |
24 | 600 | 12.0 | 6.0 |
Carbon Steel Blind Flanges
Carbon Steel Slip On Flanges
Carbon Steel Weld Neck Flanges
Carbon Steel Socket Weld Flanges
Carbon Steel Plate Flanges
Carbon Steel Lap Joint Flanges
Carbon Steel Threaded Flanges
Carbon Steel Raised Face Flanges
Carbon Steel RTJ Flanges
Carbon Steel Spectacle Blind Flange
Carbon Steel Orifice Flanges
Carbon Steel Puddle Flange
Carbon Steel Long Weld Neck Flange
Carbon Steel Flat Face Flange
Carbon Steel Anchor Flange
Type Of ASME B16.5 Flange |
Check Pressure Class Of Pipe Flange |
NPS List |
Advantages & Applications |
Very High Pressure |
All |
Pressure Testing/ Connected To Closing Pipe And Valve/ Low Price/ Easy Installation |
|
Low Pressure |
All |
Simple Installation/ Low Price/ Easy To Use |
|
High Pressure |
Small |
SW Flange For ; Smooth Bore And Better Fluid Flow |
|
Low Pressure |
Small |
Threaded Flanges (NPT/ BSP): Bore Which Matches An External Thread On The Pipe |
|
High Pressure |
All |
WN Flange use Conditions Are Critical And Severe. |
|
Low Pressure |
All |
Lap Joint Flanges Have A Long Neck And Stub End That Is Welded To The Pipe |
+91-9987870874
info@fastwell.in
Shop No. 17/B1, Ground Floor Abbas Bldg. Wing A, Jalbhai Street, Near Cama Baug Khetwadi, Grant Road (E) Mumbai – 400004. India